It is not exactly the same, but it totally filled my need for a large rustic industrial clock, and it works! My kids were pretty amazed that it actually tells time, funny. 🙂
I started with some wood that I had gotten from the cull bin at Home Depot years ago. (mine doesn't have a cull bin anymore, boo!) It was ½ inch plywood that I had ripped down into 3 ½ inch strips. I used some of this plywood for my plank wall in my master closet makeover. I decided to just use scrap barn wood for the back and glued and nailed all the plywood together. I later went back and screwed the boards on.
In the photo on the right I measured my circle. What is that I am measuring with you ask? It is PVC Lattice in white and it is 8 feet long just under 2 inches wide, and really bendy. Which is why it was perfect for my faux metal band. I didn't cut it at all, which gives an idea of how big this clock is. Since it will be the outside of the clock, it made since to use it to trace my inner clock circle.
After cutting my circle with a jigsaw, sanding it, and adding a few more support boards, I was ready to make a clock!
I used my "natural stain" which is 0000 steel wool and vinegar in a jar that has sat for at least a day or two. Then to give it a little more "old wood look" I dry brushed on some white paint very faintly.
I set to work spray painting my "metal band" with Krylon dual superbond. I knew this would ensure I wouldn't have any PVC lattice poking through my faux metal. Then I gave my lattice and carpet tacks a coat of oil rubbed bronze and then a light spritz of metallic silver. This was done from really far away it kind of gives it a hammered look but without the texture.
All this spray painting was done in 30 degree weather in my garage...I know, but it was sooo much faster to wait for the cold weather dry time rather than painting all these small pieces by hand. I kept my spray paint inside except when I was using it, and it worked like a charm.
I happened to have some small scraps of sheet metal around from another project and used it to make my roman numeral numbers. I cut them in strips with tin snips, each strip was ½ inch wide by 4 inches tall. I used a hammer on a board to flatten them out. Then I used the same spray paint method as above.
I did go to Hobby Lobby and purchase clock gear, and used a 40% off coupon. I also bought the big metal ring that is in the center of the clock at Hobby Lobby. The PVC lattice I got at Home Depot. Everything else I already had on hand so this clock was around $20 for me. Not bad for a Pottery Barn Knock Off!
In the photo on the right I am measuring the clock hands on the metal. I originally had them longer, which is how I wanted them, but my High Torque Movement wasn't as "High Torque" as expected and I had to cut them down...
Here I am attaching them with hot glue to the original hands. Too bad I had to cut them, they looked way better longer. Oh well. Sorry for the blurry picture, when I get in project mode I forget to check if my photos are good.
I measured and marked the center, and also the placement for the metal ring. In the photo I am marking where the Roman Numerals need to go, by measuring every 30 degrees from the center. This is my least favorite part, because it needs to be pretty accurate, and that takes time, so I was happy to be done!
To attach my ring, I hammered in some nails to make holes and then added wire to hold it in place. I simply twisted the wires together in the back and it is nice and secure.
Then I added my carpet tacks for the hour markers.
I used a big nail to puncture the metal for my numerals and then used my smaller nails to hammer them onto the wood. This took a while, most went in easily, but the knots in the wood really gave me some trouble in several spots.
Last up was attaching my faux metal band. I used a nail gun to hold it in place and then used screws to secure it. I had to touch up where the nails went in, but that was easy. I filled them with wood filler, then just sprayed oil rubbed bronze onto some newspaper and quickly used a small paint brush to paint the holes.
So does it look like a metal band to you?
It is close enough for me! My husband said that he thought it was metal, which made me happy.
I have to be honest, this looks way better in person. Just sayin'.
It looks so small staged on my house, but it is approx. 32 inches tall and wide.
I can't wait to get it hung up on the wall! Eeek!
I love it, even if the hands are smaller than planned. 🙂 I guess I can't get everything I want...
If you like knock off projects then come check out my Restoration Hardware Chalkboard and my Pottery Barn "It's the Most Wonderful Time of the Year Sign".
Happy Holidays!
Mindi
Sharing here:
see more of Mindi's posts on MRL below:
[categorythumbnaillist 274]
Cris
I'm just finding this amazing clock you've made - I'm not sure if you'll see my post - How did you get the ends of the PVC to stick together? Thank you!
Gail Wilson
The band is attached all the way around the outside of the "clock" with a nail gun and screws. So just tack each end close to the edge, voila! You have a faux metal band. I hope that helps!
This was my friend Mindi's project. She's pretty brilliant, eh?
gail
Pat
My experience with pvc lattice is that it expands in the summer and shrinks in the winter. Now that your clock has seen the test of time has this been a problem?
Cathy
I went shopping today. Found the PVC board at Lowe’s with the doors. Had to ask to find it. Found the metal ring at Hobby Lobby by the wooden letters and other crafting things. Found a small piece of steel sheet metal at Lowe’s too. Steel is cheaper than aluminum. Found small nails and carpet racks at Lowe’s too. Went to our antique store that has salvaged wood for the wood base. Oh and the clock parts at hobby lobby. You might have to ask but everything is out there at Hobby Lobby and Lowe’s. Can’t wait to get started.
Gail Wilson
Awesome Cathy! I'm so happy you're on your way to making this fabulous clock. Please let me know when you get it done, I'd love to see it.
gail
Mindi
I am so happy you found all the supplies Cathy! I would love to see pictures when you finish too! Best of luck! Hugs! Mindi
Kristi
HI - love your site!! Do you need different sized clock parts, depending on the actual size of the clock? Like one this big as compared to one that is, say, 1 foot across. I have tried googling the questions but am not getting good information! Thank you!
Nicole
Question about the spray painting, can you be more specific with what you did for the band versus all the other parts of the clock? Confused if the numerals are just silver or a mix.
Thanks!
Mindi
Hi Nicole! Great question, I used oil rubbed bronze spray paint on both. For the band I completely covered it with the spray paint, for the numerals I sprayed from far away with the spray paint can, enough to almost cover them. I liked the speckled look it gives to see some of the silver...but that is just personal preference. I hope that helps!
Shelly
Please share what the numbers are made of and where you got them.
Stephanie Ryckman
Hello, I'm wondering what type of nails you used to nail in the roman numerals? They look very small. Thank you.
Gail Wilson
Stephanie,
I think they're called "wire nails", you can probably find them near the picture hanging supplies at your local hardware store.
gail
Mindi
Yep Gail got it right, I used "wire nails"!
Nick
Easier way to mark where the numbers go is to put the movement in and set it to 12 and the move the minute hand around an hour and mark the hour hand at 1, then move the minute hand and mark 2, and continue on for the remaining hours.
Angie Overton
Wow! Just saying...... WOW!
Lindsey
I love this clock!! would you ever make them and sell them? I am not sure I am this crafty but love it!! 🙂
Joanne
I went to Lowes this evening and found the peice for the outside band. It was in with the interior resin moldings (resin chair rail, etc.) Hope this helps someone. Cheers ya'll!
Jenny
Just wanted to add that I also found this white lattice piece (outside band of clock) at Lowe's just this week in case anyone is looking. 🙂
Kendra
Thanks for posting!! I was wondering where to get that!!! For the inner band too?
Kathy Sheeran
Still on this PVC thing...I looked on Home Depot website and all i find in lattice is end cap and divider and those are only 48 in and are not flat...Anyone find this?
Mindi
Hi Kathy, sorry you have been having a hard time finding this, it is difficult to find. Here is the link to what I bought at Home Depot. http://www.homedepot.com/p/Royal-Mouldings-6510-1-4-in-x-1-3-4-in-x-8-ft-PVC-Composite-White-Lattice-Moulding-0651008005/202089995
Allex
I did, I found one less than 2" wide and 8' long. hmmmm.... maybe is different in every HD. Good luck Kathy, don't give up.
http://www.homedepot.com/p/Royal-Mouldings-6510-1-4-in-x-1-3-4-in-x-8-ft-PVC-Composite-White-Lattice-Moulding-0651008005/202089995?cm_mmc=Shopping%7CTHD%7CG%7C0%7CG-BASE-PLA-D30-Moulding%7C&gclid=CIe_me7VnM4CFYmBfgodb7gCQg&gclsrc=aw.ds
6510 1/4 in. x 1-3/4 in. x 8 ft. PVC Composite White Lattice Moulding
Joanne
I found it at Lowes with the RESIN moldings (resin chai rail, etc.).
Kathy Sheeran
This pvc lattice is a mystery to all the home depot employees...we looked at every piece of plastic type 8 ft pieces and did not find what you used...maybe a close up of the piece would help or a sku number...Really cannot find this stuff...please help
Thanks
Yvonne
I have found that pvc lattice before. I used it as baseboard in a wet space. I believe i found it with the non-wood baseboard molding "Lumber". I remember being surprised that it was called lattice board.
gail@myrepurposedlife.com
I've had trouble finding it at my Home Depot too. 🙂 Why do they have to "hide" good stuff!
gail
Allex
Model # 0651008005 Internet # 202089995 Store SKU # 843640
Hope this work if you still looking.
Tina Verma
Oh my goodness! Thank you so much for sharing this. Our 5th anniversary is coming up and I wanted to make my husband something out of wood that we could share in our new home. This went perfectly with the wine bottle vases and cork candles I had already finished to decorate the mantle. I wish I could post a picture of my results here because (if I do say so myself) it's FABULOUS! THANK YOU!
Kathleen
Hi Mindi!
I read that you bought the clock parts at Hobby Lobby, but the hands too? I can only find flimsy hands they sell at Hobby Lobby; the ones you glued hands to look more sturdy. Did you buy them at Hobby Lobby too? Thanks! Awesome clock!
Esther Bunny
I like yours better.
Linda
Where did you get the PVC white lattice you used for the outside of the clock? I can't seem to find it at Home Depot or Lowes. They do have some but it has holes all around it. Thanks Linda
Mindi
Hi Linda, I actually found the PVC lattice in the very back of the store kind of past where all the moldings and trim are, I would start there and then ask. It should be in the trim/moldings area somewhere, in the plastic section...I hope that helps, good luck! Oh, and I found mine at Home Depot.
Mariann
I love this idea! It's not question. But very difficult to buy anything about this project.
I would like to ask, where can I bay faux metal band? I didn't see any metal ring in the hobby lobby....
So, now I'm so disappinted. I really love this clock. Any idea?+
gail@myrepurposedlife.com
Mariann,
The faux metal band is actually PVC lattice found at your hardware store. The metal ring was found at hobby lobby, maybe you could ask them, or try michaels.
good luck!
gail
Linda J
You sure hit the nail on the head with this one! It is now on my project list. Thanks for the DETAILED instructions. As I read, you answered every question that came to mind. I can't wait to get started!
Kaitlin
Absolutely love the idea. I've made square and rectangular shaped clocks before for Xmas presents. Now I'm really thinking of making this for my mom for mother's day. She has an outstanding back deck, and I think this will go great!
I am concerned about how I would hang this, though. It seems quite heavy! Any tips?
jessica
AHH I heart this! I have the top of a pallet that I am turning into a clock. I dont know if I will be able to think of things now after seeing this lol.
I hope you had a great Easter!! I pinned and shared this!
Jess
Donna
you did an amazing Job! I need to find some wood! Thank you for the tutorial
Erlene
Wow, wow, and wow! That's amazing and you only spent $20!
Kirsten @ Treat Yourself Sweeter
Oh, I WANT this clock but have serious doubts in my DIY skills. Might be one for my mum and I to tackle together., Thanks for the great instructions!! 🙂
Kim
OMG! Awesome! Great job! Yours is better lol.
Mary
Wow that looks fabulous. I enjoyed seeing a clock kit... I didn't know about such. I have a large broken clock I picked up for free. Now I know I can repair it and update it. I'm glad you posted
Richard McMahan
My wife sent this pin saying that she loved it so I set to work. I really appreciate the step by step instructions. Made this a pretty simple yet awesome project! I can't figure out how to add a picture to the comment or I would post one. Also I made mine from pallet wood and some scrap sheet metal so I have only about $30 in it (although I feel the hands are a bit small on mine.) Thanks again!
Ted
Where did you find the brass metal ring you placed in the center of the clock?
Looks great!
Thanks
Ted
Mindi
Thanks so much Ted! I got it at Hobby Lobby in the craft section, it was the largest size they had.
Juanita
Absolutely love it Mindi!!!
To anyone in Australia.... any idea where might be able to get the inner metal ring?
Thanks
Juanita
The closest I can find is this vege plant trellis thing, but it is only 32cm (12.5")?
Maureen
Hi Mindi!
Love what you have done here! Would you mind letting me know the measurements of your clock hands? I'd like to see if I can find some larger ones, but having a reference number would be helpful. Thank you! And again, love your work!
Contessa EauCrafty
I like yours better than theirs. Thanks for the inspiration!
Contessa
Jordana Maendel
Hi, I'm wondering what exactly the "PVC Lattice" is, and where would i find it?
gail@myrepurposedlife.com
Mindi told me....
I found the PVC lattice in the very back of the store kind of past where all the moldings and trim are.
gail
Patricia
The Honey keeps telling me he'd like a big huge clock! I really need to get off my B...ehem, back-side and make one of these! You make it look so easy. 🙂
Nice knock-off Mindi
Merry Christmas to you!
And Merry Christmas to you too Gail!
I know I'm late... but, well, Gail, you know how I procrastinate. 😉 Patricia
Rebecca Axtman
I love your "Pottery Barn" clock. I have huge walls that need HUGE pieces so I'm thinking I'll flatter you by copying your clock. Any other ideas on bigger clock hands, after you've done it?
Julie @ follow your heart woodworking
Lovely job again, Mindi. That outer "metal" ring is just so cool. I must remember this... it's a great idea for a border for a round sign (and I make a lot of those). I, too, am often stopped in my tracks by knots where I don't want them to be! LOL
Mei
Your copy cat rustic clock is amazing. I have been wanting to make a feature clock for my house. Thank you for sharing your talent with the world.
Mei a.k.a. The New Vintage
Kristen Jorg
I have 2 questions
1. Is the pvc piece you used perfectly round?
2. How wide is the diameter of the metal ring? I am working on a project that requires 2 rings of 26" diameter. Having a hard time finding what I need. Can you suggest anything?
Thank you,
Kristen
Mindi
Hi Kristen,
The PVC piece is a long straight piece that I bought at 8 feet long. I just clamped it together at the ends and it made a circle. It looked good to me but I couldn't guarantee that it is perfect. 🙂 I used it to trace my clock size and then nailed and screwed it around the clock (see post for details). As for your second question, the metal ring is 19 inches wide, it is the biggest one I could find at Hobby Lobby. I am not sure where you could get one bigger, but you could use the PVC Lattice to make 26 inch circles, although it might be hard for them to keep their shape without attaching them to something, so you would have to think of a way to secure the end pieces to keep it a circle. I guess it depends on what you need your rings for. I hope that helps!
Mindi
Janet
Did You Use Flashing For the numbers? We are making this awesome clock for our daughters Christmas!
Bliss
Must I really tell you how awesome that is? Must I tell you once again I pinned this to make my own? Must I?
gail@myrepurposedlife.com
Mindi!
Another great project! I love your Pottery Barn rustic clock knockoff!!!
Bliss
I totally agree with you! Mindi is smart and creative.... to use that pvc piece for the circle? genius!
gail